SAE-J1708

关键词: SAE-J1708,J1939-协议堆栈 J1939

简介：J1708 software OurJ1708Device Driver provides a simple application program interface (API) for sending and receiving SAE J1708 messages. It is designed to work with our J1587 software and abstracts away the technical details and many complexities associated with message timing and interfacing to the physical layer. This increases the simplicity of your application software, improves your reliabili...
品牌	ixxat
产地	德国
型号	PXF3271
折扣	其他电询

咨询专家:

	黄工-工业总线-工业自动化-实时仿真 ID：2937
	机电电子工程专业硕士，机械设计制造及其自动化/计算机双学士，高级工程师具有丰富的从业、管理经验，曾在机电工程公司，资深设计代理公司工作。历任组织、经理等岗位，同时具有深厚的理论基础和项目项目研发经历。...
	[MORE]

	赵工-总线系统-嵌入式系统-工业自动化 ID：2940
	机械电子工程，嵌入式系统专家，高级工程师嵌入式项目开发，ARM，Freescale，Infilion等系列单片机系统开发，DSP嵌入式系统开发，FPGA系统开发，项目经验丰富。 ...
	[MORE]

产品说明:

J1708 software

Our J1708 Device Driver provides a simple application program interface (API) for sending and receiving SAE J1708 messages. It is designed to work with our J1587 software and abstracts away the technical details and many complexities associated with message timing and interfacing to the physical layer. This increases the simplicity of your application software, improves your reliability, and shortens your product s time to market.

The J1708 device driver was designed by Simma Software and has been used in numerous automotive embedded systems. Also, it has been validated to withstand 100% bus utilization on multiple networks simultaneously. If you have questions about J1708, try our J1708 Introduction.

J1708 Software Details:

MISRA C compliant
ANSI C source code
Use with or without an RTOS
Supports Multi-frame messages
Use with 8, 16, 32, or 64-bit CPU
Use with J1587/J1708 flash bootloader
ssJ1708 user’s manual

SAE J1708

The SAE J1708 specification was defined by the SAE and TMC in 1986. Its main purpose is to address the transmission of electronic signals and information among truck and bus components (i.e. Electronic Control Units or ECUs).

J1708 is mainly used on heavy-duty and commercial vehicles. It defines the physical layer and data link layer. Common application and transport layers used on J1708 are J1587 and J1922. J1587 communicates diagnostic information, while J1922 communicates control data. J1708 is outdated and is currently being phased out of production. It is being replaced by j1939.

J1708 Data Link

J1708 is a differential serial communications bus which is half duplex and multi-master (i.e. multi-drop). It uses 8, N, 1 byte framing and has a network speed of 9600 bits per second (bps). The first byte of every message is the MID, which stands for message identifier. Every message ends with a twos complement checksum.

J1708 Physical Layer

J1708 uses a twisted pair of wires, with a minimum wire size of 18-gauge. The wires should have one twist per inch and have a maximum length of 40 meters. A RS-485 transceiver connected in passive mode is used as the bus transceiver. It is important to note, that the transceiver should not be used in active mode which is normally used for RS-485 networks. The reason for this is passive mode allows for non-destructive bus arbitration.

J1708 Bus Termination

J1708 networks do not use bus termination. Instead, using 47 ohm resistors, each node is impedance matched to the network.

J1708 Bus States

The logical value transmitted onto the bus is the difference in voltage between the two wires. A logical 1 is when wire A is more than 0.2V than wire B. A logic 0 is when B is 0.2V more than A. When the voltage difference is less than 0.2V, the bus state is undefined.

J1708 Idle Time

The bus is considered idle if there is no activity (i.e. logic state of 1) for at least 10 bit times, or 1.0417 ms. Once the bus is idle and the device has waited it corresponding priority based delay time, a device may start transmission.

J1708 Priority

In J1708, each message is defined a priority. There are 8 different priorities, ranging from 1 to 8. The priority defines how much additional time must transpire after the bus has become idle before a node may transmit. A priority 1, which is the most critical, waits an additional 0.2 ms after the bus is idle. Each subsequent priority adds an additional 0.2 ms.

J1708 Inter-character Bit Time

For bytes to be considered as part of a message, the time between bytes is not allowed to exceed 2 bit times. If this time is exceeded, the message is not valid.

J1708 Bus Access Time

The time between the last time the ECU (i.e. software) checked the state of the network and when it starts to send the falling edge of the start bit for the first byte, is known as the bus access time. The maximum allowed bus access time is 50 microseconds. If this time is exceeded, UART based framing errors may occur on the bus. Because of this, it is critical that ECUs guarantee bus access time compliance.

J1708 Checksum

The last byte of every message is the two s complement of the MID and data contained in the message.

J1708 Message Length

The maximum length, from the MID to the checksum, is 21 bytes. If the engine is not running and the vehicle is not moving, messages longer than 21 bytes may be transmitted.

J1708 Application Layer

For J1708 message definitions on a J1708 network, see J1708, J1587, J1922, or J2497. Selecting which document is determined by the MID of the message. SAE J1708 contains a table which ties each MID, and message, to a particular document.

SAE J1708 Ports

Our real-time SAE J1708 device driver is written in the ANSI C programming language. It is target specific and incorporates the details for a given microcontroller.

Together ssJ1587 and ssJ1708 form a complete ported system allowing customers to be up and running on a J1587/J1708 network almost immediately. Our ssJ1708 device driver has been ported to over 15 different microcontrollers. Below is the list of available ports. Please contact us if you are interested in a port or device driver for a hardware platform that is not listed.